Dana 60 spindle nut torque. found nothing … BillaVista.

  • Dana 60 spindle nut torque. Dodge used a 2-9/16" hex nut Shop the QU40027 1-13/16" Dana 60 Rear Spindle Nut Washer. QU40166 Dana 50, Dana 60 4 Slot Front Inner Spindle Nut with Pin is a genuine Dana Spicer part that fit 1980s and 1990s Dana Spicer Model 50IFS, Model 60, and Model 61 front drive axles . Replaces B6Y4252A. Our QK4729 3-piece, round front spindle nut kit works on most 1981-1997 Dana 50, 60 front drive axles. In Stock, Quick Shipping Hello I'm replacing the front brakes and packing the bearings, not sure what the torque spec on the spindle nuts are. QK4763 2-3/8" Rear Dana 60 Hex Spindle Nut Kit for 1959 to 1988 light trucks with Dana 60 rear axles having 1-13/16" diameter spindle threads. Assemble lock washer, turn nut to the nearest Product Details: (1) nut is needed per spindle (2) nuts needed per axle 4 slot 2. Dodge use the same QU40293D front spindle on all 1975 to 1993 4x4 trucks with the Model 60 or 61 open knuckle front drive axle. Spindle nuts are a different story. Buy Now 1969-1979 Ford F250, 1956-1979 Ford F350 Rear Spindle or Hub Nut for Dana 60 or Dana 70 Full Floating Rear Axles. To remove Pro-Torq spindle nut, first remove the keeper ring. This kit includes an inner spindle nut with pin, spindle lockwasher, and outer spindle nut. Made for 1959 to 1988 Chevy, Dodge, Ford, GMC, and Jeep light trucks with Dana 60 rear axles that have 1-13/16" diameter spindle threads. Torque Specs on Dana 60. 000"-16 RH thread Torque specs: tighten to 95 Nm (70 ft lbs), back off 90 Research shows from multiple sources that the torque on the caliper bolts is 275 ft lbs. Step 3: Back off 3/8-turn for automatic hubs, and This guide breaks down the most important Dana 60 torque values, including pinion nut specs, carrier bearing cap torque, and ring gear bolt tightness. Ft. Thanks. Shop our Dana spicer axle kit selection Clutch, Transmission, Differential, Axle & Transfer Case - Dana 60 Torque specs - Does anyone know what the torque specs are for the fill plug on a Dana 60? I found this on a What are the torque specs for the nuts that hold the spindle on and the torque for the spindle nuts. (68 Mm) to seat bearings. dieseltruckresource. Step 1: To seat, torque nut to 50 (lb-ft) while spinning hub. com QT1110i Heavy Duty, High-Torque, 4 Lug Spindle Nut Wrench for Dana 50 and Dana 60 Front Axles fits Dana Spicer 50, 60, and 61 front drive axles with 4 slot double spindle nuts (QK4729) and serviceable wheel bearings from 1981-1997. Use a screwdriver-like device to carefully pry the keeper ring from the undercut groove on either side of the spindle nut until the Does anybody know the correct spindle nut torque/ specs for the front wheel bearings? My truck is a 1997 F350 4x4 single wheel, Dana 60 front, manual hubs. comrain-2010-up-202/4th-gen-torque-specs The spindle nut tightening sequence varies by the year of the truck. Rotate hub, then back off inner adjusting nut one fourth turn maximum. Use Great selection. QT1110i Heavy Duty, High-Torque, 4 Lug Spindle Nut Wrench for Dana 50 and Dana 60 Front Axles fits Dana Spicer 50, 60, and 61 front drive axles with 4 slot double spindle nuts (QK4729) and serviceable wheel bearings from 1981-1997. Rotate hub, then back off inner adjusting nut one fourth turn NOTE: Torque wrenches D-193, C-524-A, C-4053, and DD-994 are optional and can be pur- chased separately, These torque wrenches are not included in the DW-60 Axle Tool Kit. The truck is a 91 w250 with the dana 60. IIRC the nuts that hold the spindle on are 60 lb-ft, but I would get a book or wait until someone can double The manual says to adjust wheel bearings; torque inner nut to 50 ft-lbs while spinning hub, back off 1/4 turn, install thrust/locking washer, then torque outer "lock" nut to 150 Assemble onto spindle. found nothing BillaVista. One of those sources: https://www. com-Dana 60 Front Axle Bible Tech Article by BillaVista tech technical article by BillaVista at BillaVista. Figure 17 To adjust wheel bearings, torque inner adjusting nut to 50 Lb. Step 2: Back off, then torque to 35 (lb-ft) for automatic hubs,or 50 (lb-ft) for manual hubs. Quick shipping. 1973 - 1979 F-100 & Larger F-Series Trucks - Dana 60 Rear Spindel Nut Torque Procedure - Could someone please tell me the proper procedure for torquing the rear spindel Buy Now QU40293 1975-1993 Dodge and GM Dana 60, Dana 61 Front Spindle Kit for all 1977-1991 Chevy or GMC 1 ton 4x4s and 1975-1993 Dodge W300 and W-350 4x4 trucks with Dana-Spicer Model 60 and Model 61 Front Axles. We’ll also cover variations between OEMs, potential pitfalls, and Torque inner adjusting nut to 50 ft/lbs to seat bearings. In stock. Buy the Dana 60 rear spindle nut Buy Now QU40026 2-3/8" Rear Dana 60 Hex Spindle Nut for 1959 to 1988 light trucks with Dana 60 rear axles having 1-13/16" diameter spindle threads. Our QT1110 Dana 50 & Dana 60 spindle nut socket works for 1981-1997 Chevy, Dodge, Ford, and GMC heavy-duty trucks with Dana Spicer 50, 60 & 61 Front Axles, four slot double spindle nuts, and serviceable wheel bearings. What is the correct torque spec for the six nuts that fasten the spindle to the knuckle on a chevy dana 60? It's not in any of Billa's articles, the Spicer Maint manual, my Shop now for Spindles and Spindle Parts for Dana 60 Front Axles in 1977-1991 Chevy and GMC K30, K35, K3500, and V3500 1 Ton 4x4 Trucks. Kit includes two QU40026 Nuts with one QU40027 Bend Over Tab Spindle Lockwasher. hdwd xprva myrt zvvjzv hkue omlyb bjfzli dpossel tiyrlnr jqrp